扭剪扳手初擰需要用哪種扳手？實際上，扭剪型高強螺栓的初緊可使用沖擊電動扳手或定扭矩扳手，而終緊須使用扭剪扳手，所以扭剪扳手是專門終緊扭剪型高強螺栓的。
What kind of wrench is required for the initial tightening of the shear wrench? In fact, the impact electric wrench or fixed torque wrench can be used for the initial tightening of torsional shear high-strength bolts, and the torsional shear wrench must be used for the final tightening, so the torsional shear wrench is specially used for the final tightening of torsional shear high-strength bolts.
初擰扳手，可用電動扳手也可用手動帶響扳手。但無論用哪種扳手施工前都須進行標定，以便控制初擰扭距值。手動扳手作為終擰工具時，須每班進行標定，并做好標定記錄。扭剪型高強螺栓是一種自標量型螺栓，因此終擰只須把高強螺栓尾部螺栓頭擰掉即可，扳手不用標定。
For the initial tightening of the wrench, the electric wrench or the manual ring wrench can be used. However, no matter which wrench is used, calibration must be carried out before construction to control the initial tightening torque value. When the hand wrench is used as the final tightening tool, it shall be calibrated every shift and the calibration record shall be made. Torsional shear high-strength bolt is a self-scalar bolt, so the final tightening only needs to unscrew the bolt head at the end of the high-strength bolt, and the wrench need not be calibrated.
扭剪型高強螺栓，其顯著標志就是螺桿前頭有一個梅花頭，終緊的時候就是以把梅花頭打斷作為終緊完畢。須采用電動力矩扳手來進行安裝。只有當力矩達到要求后，高強螺栓的梅花頭才會被擰掉，這樣可以保證所使用的螺栓達到須的預緊力從而保證性能。所以在工程中可以通過檢查梅花頭是否還在還判斷高強螺栓是否起到作用，而扭剪型高強螺栓都是一次性也是因為這個原因。
Torsional shear high-strength bolts have a plum head at the front of the screw, and the final tightening is completed by breaking the plum head. Electric torque wrench must be used for installation. Only when the torque meets the requirements, the Torx head of the high-strength bolt will be screwed off, which can ensure that the bolts used reach the required preload and thus ensure the performance. Therefore, in the project, it is possible to determine whether the high-strength bolt works by checking whether the plum blossom head is still in use. This is also the reason why the torsional shear high-strength bolt is disposable.
那么
扭剪螺栓專用扳手廠家結合經(jīng)驗所認為，根據(jù)高強螺栓的施工工藝要求，高強螺栓的施工須先初擰后終擰，初擰高強螺栓需用沖擊型電動扳手或扭矩可調(diào)電動扳手；而終擰高強螺栓有嚴格的要求，終擰扭剪型高強螺栓須用扭剪型電動扳手，終擰扭矩型高強螺栓須用扭矩型電動扳手。
According to the experience of the manufacturer of special wrench for torsion and shear bolts, according to the construction process requirements of high strength bolts, the construction of high strength bolts must be carried out first before final tightening, and the initial tightening of high strength bolts requires impact type electric wrench or torque adjustable electric wrench; However, the final tightening of high-strength bolts has strict requirements. The final tightening of shear-type high-strength bolts must use a shear-type electric wrench, and the final tightening of torque-type high-strength bolts must use a torque-type electric wrench.
一般的扭剪型高強螺栓的初緊會選擇手動扳手、沖擊電動扳手、電動扭矩扳手或者專門的初緊扳手，而終緊扭剪型高強螺栓就須選擇電動扭剪扳手，而不能選擇扭矩扳手。（因為終緊的時候須要把梅花頭打斷，只有扭剪扳手有這個功能。）
Generally, manual wrench, impact electric wrench, electric torque wrench or special initial tightening wrench will be selected for the initial tightening of torsional shear type high-strength bolts, while electric torsional shear wrench must be selected for the final tightening of torsional shear type high-strength bolts instead of torque wrench. (Because the box end needs to be broken when final tightening, only the torsion wrench has this function.)
終擰緊固時應注意，待梅花頭全部套入套筒后，才能按下電動扳手開關，若內(nèi)套筒只套入梅花頭尺寸的1/3～1/2長度時按下電動扳手開關，將會造成梅花頭打滑，并且影響套筒的使用壽命。緊固時，終擰電動扳手應和構件摩擦面保持垂直，扳手傾斜是很容易導致螺栓尾部梅花頭打滑，并易卡殼。
During final tightening, it should be noted that the electric wrench switch can only be pressed after the ring head is fully inserted into the sleeve. If the inner sleeve is only inserted into 1/3~1/2 of the size of the ring head, pressing the electric wrench switch will cause the ring head to slip and affect the service life of the sleeve. When tightening, the final tightening electric wrench should be vertical to the friction surface of the component. The wrench tilt is easy to cause the bolt tail to slip and jam.
Thank you for your reading. The source of this article is: What kind of wrench is required for the initial tightening of the wrench? For more information and questions, please click: http://www.tj-feiya.com We will continue to work hard to provide you with services. Thank you for your support!
