在線留言|
您好，歡迎來到 濟南萬中電動扳手有限公司網站！
服務熱線： 400-117-8816
13406879330
13406879330
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家
用扳手內套筒插進螺栓尾部梅花頭部分，同時向前推動扳手，內套筒后退，使外套筒*套住螺母，若不能*套住螺母請左右轉動扳手并向前用力。
Insert the inner sleeve of the wrench into the end of the bolt's plum blossom head, while pushing the wrench forward and the inner sleeve backward, so that the outer sleeve * fits the nut. If it cannot * fit the nut, turn the wrench left and right and apply force forward.
扣動扳手開關，使其旋轉。擰斷梅花頭，緊固結束，同時扣動扳機彈出梅花頭。
Turn the wrench switch to rotate it. Twist off the plum blossom head, tighten it, and at the same time pull the trigger to pop out the plum blossom head.
扭剪型電動扳手注意事項：
Precautions for torsion shear electric wrench:
本機所用電源應在本機規定的范圍內，否則會造成機器故障。
The power supply used in this machine should be within the specified range, otherwise it may cause machine failure.
不可在雨天或潮濕的環境中使用本機，以免漏電。
Do not use this machine in rainy or humid environments to avoid electric leakage.
使用本機高空作業時，請系好帶，在操作點下方嚴禁站人及放置貴重物品。
When using this machine for high-altitude operations, please fasten your seat belt and strictly prohibit standing or placing valuable items below the operating point.
使用本機時需遠離易燃易爆物品。
Keep away from flammable and explosive materials when using this machine.
嚴禁破壞電源線及使用電源線拖拉本機。
It is strictly prohibited to damage the power cord and use the power cord to drag the machine.
檢查及維修本機時應先切斷電源。
When inspecting and repairing this machine, the power should be cut off first.
嚴禁過重碰撞本機。
Excessive collision with this machine is strictly prohibited.
當機器發燙或環境溫度大于35℃時，應停止使用。
When the machine becomes hot or the ambient temperature exceeds 35 ℃, it should be stopped from use.
定期檢查碳刷，當碳刷長度小于原長度2/5時，應及時更換。
Regularly inspect the carbon brush, and replace it in a timely manner when the length of the carbon brush is less than 2/5 of the original length.
扭剪型電動扳手檢查與維修：
Inspection and maintenance of torsion shear electric wrench:
定期檢查電源線，如果有破裂或斷線應及時更換。
Regularly check the power cord and replace it promptly if there is any breakage or disconnection.
保持內外套筒清潔不得混入雜物。用完本機后應擦拭干凈存放于干燥處。
Keep the inner and outer sleeves clean and free from debris. After using this machine, it should be wiped clean and stored in a dry place.
使用前應檢查各緊固螺釘是否松動，如果松動應及時緊固，并試轉聲音是否正常，如果出現異常聲音應及時檢修。
Before use, check whether each fastening screw is loose. If it is loose, tighten it in a timely manner and test whether the sound is normal. If there is any abnormal sound, repair it in a timely manner.
